Saturday, 21 November 2026

The idea is simple: you do not wait for a fire, you work through the risk before work starts, put controls in place, and keep checking them.

 This poster is a full workflow for fire and explosion safety. The idea is simple: you do not wait for a fire, you work through the risk before work starts, put controls in place, and keep checking them.



The slogan at the top sums it up: Identify, Assess, Control, Review.


The 8 steps


1: Prepare for Assessment

Before you look at any hazard, you define what you are assessing. That means the area, the activity, and the equipment involved.


You also gather information: what process and materials are involved, the Safety Data Sheets (SDS), previous incidents, and the standards that apply like NFPA and OSHA. And you pick a competent team to do it, not just one person working alone.


2: Identify Hazards

This is where you list what could actually burn or explode.


For fire, that is sources like hot work, electrical faults, and mechanical friction or heat. For explosion, that is flammable vapours, gases, and combustible dusts.


You also list potential ignition sources. A fuel without an ignition source is still a risk, but it becomes a fire or explosion when the two meet.


3: Assess the Risk

Now you rate each hazard you find.


You ask two questions:

How likely is it to happen, meaning how often could it occur?

How severe would the consequence be if it did?


You plot those two answers on the matrix in the poster, Likelihood on one side and Consequences on the other. The result gives you a risk level: Low, Medium, High, or Extreme. That rating tells you how urgently you need to act and how strong the controls must be.


4: Identify Controls

Once you know the risk level, you choose controls using the hierarchy of controls. The higher up the list, the more effective it is.

| Priority | Control | What it means in practice |


| 1 | Eliminate the hazard | Remove the flammable material or stop the risky job entirely 


| 2 | Substitute with safer option | Use a less flammable liquid or a safer method 


| 3 | Engineer controls | Add ventilation, explosion protection, or separation 


| 4 | Administrative controls | Use procedures, permits, signage, and training 


| 5 | PPE | Use flame resistant clothing, respirators, and other protective gear 


PPE is last because it does not stop the fire, it only protects the person if the other controls fail.


5: Implement Controls

This is putting the plan into action. Install the controls, make sure PPE and equipment are used correctly, and follow safe work procedures like a Permit to Work (PTW) for hot work.


The poster shows a worker at a “No Ignition Sources” switch. That is a good example. The control is not just written down, it is physically applied at the job site.


6: Review and Monitor

Controls can fail or conditions can change, so you monitor them.


That includes checking gas levels, temperature, and other conditions, and checking that controls are still working. The gas detector in the poster shows LEL 0%, which means Lower Explosive Limit. At 0%, no flammable gas is detected at that moment.


You also review if anything changes in the process, equipment, or conditions.


7: Communicate and Train

A risk assessment that stays in a file does not protect anyone.


You share the results with all affected personnel, provide training and refreshers, and display warning signs where needed. Everyone who could be exposed should know what the risk is and what to do.


8: Document and Review

Finally, you record the assessment, the controls, and the actions taken in a formal Risk Assessment Report.


You review it regularly, and also when:

Process or equipment changes

New hazards are identified

After an incident


That review sends you back to step 1. It is a loop, not a one time task.


The three boxes at the bottom


Key Fire and Explosion Risk Factors: These are the things that make a fire or explosion more likely. Flammable liquids, gases, and dust. Ignition sources like hot work, electricity, and static. Poor ventilation that lets vapours build up. Incompatible materials stored together. High temperature and pressure that make a release or ignition worse.


Common Control Measures: The everyday controls that prevent most incidents. Good housekeeping to avoid spills and dust build up. Adequate ventilation. Controlling ignition sources. Using explosion protection like Ex rated equipment. And having emergency preparedness and response ready.


Remember: Assess the risk, control the hazard, prevent fire and explosion.


In short, the poster is asking you to find the fuel and the spark before they meet, decide how bad that meeting could be, stop it with the strongest control you can, and then keep checking that the control still works. 🚨🚥🗼⚠️🌡️🚧⛑️🚦🦺🏗️

#viralreelschallenge #ConstructionSafety #facebookviral #SafetyCulture #viralreels #ToolboxTalk #fypシ #safetyfirst #fyp #safety

No comments:

Post a Comment